Raid software
par
popularité : 6%
A. RAID de niveau 0 et 1 ( tester sous RedHat 6.2 )
-
Configurez le fichier /etc/raidtab de cette manière :
raid de niveau 0
raid de niveau 1
raid de niveau 5
<table border="0"> raiddev /dev/md0 raid-level 0
nr-raid-disks 2
nr-spare-disks 0
chunk-size 4
persistent-superblock 1
device
/dev/hda5raid-disk
0
device
/dev/hda6
raid-disk
1raiddev /dev/md0 raid-level 1
nr-raid-disks 2
nr-spare-disks 0
chunk-size 4
persistent-superblock 1
device
/dev/hda5
raid-disk0
device
/dev/hda6
raid-disk
1raiddev /dev/md0 raid-level 5
nr-raid-disks 7
nr-spare-disks 0
persistent-superblock 1
parity-algorithm left-symmetric
chunk-size 32
device /dev/sda3
raid-disk 0
device /dev/sdb1
raid-disk 1
device /dev/sdc1
raid-disk 2device /dev/sdd1
raid-disk 3
device /dev/sde1
raid-disk 4
device /dev/sdf1
raid-disk 5device /dev/sdg1
raid-disk 6
Si vous souhaitez mettre un/des disques
des secours, alors il faudra ajouter :
device /dev/sdh1
spare-disk 0
Formatez les partitions avec cette commande :
/sbin/mkraid /dev/md0 /sbin/mke2fs /dev/md0
Création du répertoire de montage et montage du FS
mkdir /raid0/ /sbin/raidstart /dev/md0 mount /dev/md0 /raid0
Pour finir :
Monter le périphérique raid au démarrage
/etc/rc.d/rc.local et ne vous ennuyez pas à le mettre
dans le fichier /etc/fstab. Ca ne marchera pas!
Pour arrêter, un système raid:
Démonter le et faire /sbin/raidstop /dev/md0
Pour le lancer:
/sbin/raidstart /dev/md0 (ou le périphérique ) et
monter le device.
B. Divers
cat /proc/mdstat
| inactif | actif | |
Raid 0 | Personalities : [raid0] read_ahead 1024 sectors unused devices : <none> |
Personalities : [raid0] read_ahead 1024 sectors md0 : active raid0 hda6[1] hda5[0] 104576 blocks 4k chunks unused devices : <none> |
Raid 1 |
Personalities : [raid1] read_ahead 1024 sectors unused devices : <none> | Personalities : [raid1] read_ahead 1024 sectors md0 : active raid1 hda6[1] hda5[0] 52288 blocks [2/2] [UU] unused devices : <none> |
Fichier /etc/raidtab :
| raiddev device | This introduces the configuration section for the stated device. |
| nr-raid-disks count | Number of raid devices in the array ; there should be count raid-disk entries later in the file. (current maximum limit for RAID devices -including spares- is 12 disks. This limit is already extended to 256 disks in experimental patches.) |
| nr-spare-disks count | Number of spare devices in the array ; there should be count spare-disk entries later in the file. Spare disks may only be used with RAID4 and RAID5, and allow the kernel to automatically build new RAID disks as needed. It is also possible to add/remove spares runtime via raidhotadd/raid hotremove, care has to be taken that the /etc/raidtab configuration exactly follows the actual configuration of the array. (raidho tadd/raidhotremove does not change the configuration file) |
| persistent-superblock 0/1 | newly created RAID arrays should use a persistent superblock. A persistent superblock is a small disk area allocated at the end of each RAID device, this helps the kernel to safely detect RAID devices even if disks have been moved between SCSI controllers. It can be used for RAID0/LINEAR arrays too, to protect against accidental disk mixups. (the kernel will either correctly reorder disks, or will refuse to start up an array if something has happened to any member disk. Of course for the ’fail-safe’ RAID variants (RAID1/RAID5) spares are activated if any disk fails.) |
| Every member disk/partition/device has a superblock, which carries all information necessary to start up the whole array. (for autodetection to work all the ’member’ RAID partitions should be marked type 0xfd via fdisk) The superblock is not visible in the final RAID array and cannot be destroyed accidentally through usage of the md device files, all RAID data content is available for filesystem use. | |
| parity-algorithm which | The parity-algorithm to use with RAID5. It must be one of left-asymmetric, right-asymmetric, left-symmetric, or right-symmetric. left-symmetric is the one that offers maximum performance on typical disks with rotating platters. |
| chunk-size size | Sets the stripe size to size bytes. Has to be a power of 2 and has a compilation-time maximum of 4M. (MAX_CHUNK_SIZE in the kernel driver) typical values are anything from 4k to 128k, the best value should be determined by experimenting on a given array, alot depends on the SCSI and disk configuration. |
| device devpath | Adds the device devpath to the list of devices which comprise the raid system. Note that this command must be followed by one of raid-disk, spare-disk, or parity-disk. Also note that it’s possible to recursively define RAID arrays, ie. to set up a RAID5 array of RAID5 arrays. (thus achieving two-disk failure protection, at the price of more disk space spent on RAID5 checksum blocks) |
| raid-disk index | The most recently defined device is inserted at position index in the raid array. |
| spare-disk index | The most recently defined device is inserted at position index in the spare disk array. |
| parity-disk index | The most recently defined device is moved to the end of the raid array, which forces it to be used for parity. |
| failed-disk index | The most recently defined device is inserted at position index in the raid array as a failed device. This allows you to create raid 1/4/5 devices in degraded mode - useful for installation. Don’t use the smallest device in an array for this, put this after the raid-disk definitions ! |
Commentaires Forum fermé